Current-Loop Scr Control
#current-loop
#SCR
#isolated drive
#4-20mA
#one-shot
#Q2
#control circuit
#industrial control
#power electronics
Description: This circuit enables a 4-to-20 mA current loop to control an isolated SCR drive. IC1A and IC1B function as one-shot timers. Q2 detects zero crossings of the 120 Vac line, which triggers one-shot IC1B. IC1A causes Q1 to discharge capacitor C2. When C2 recharges through resistor R2, it triggers IC1A, along with the optoisolator and SCR1/SCR2. The triggering of SCR1 and SCR2 is dependent on the input current, allowing for control over motor speed, light intensity, and similar applications.
This circuit is designed to facilitate the control of devices such as motors and lighting systems through a 4-to-20 mA current loop, which is a standard in industrial automation for transmitting analog signals. The operation begins with the detection of zero crossings from the 120 Vac line by transistor Q2. This detection is crucial for synchronizing the control signals with the AC line frequency, ensuring that the SCRs are triggered at the correct phase of the AC cycle.
IC1A and IC1B are configured as monostable multivibrators, commonly referred to as one-shots. When Q2 detects a zero crossing, it sends a pulse to IC1B, which generates a timed output pulse. This output pulse is used to control the state of the SCRs, effectively allowing for the modulation of power delivered to the load.
Simultaneously, IC1A is responsible for managing the timing of capacitor C2. When triggered, IC1A causes Q1 to discharge C2, which subsequently begins to recharge through R2. The timing characteristics of this process determine the frequency and duty cycle of the output signal to the SCRs, thereby directly influencing the power delivered to the load.
The optoisolator serves to provide electrical isolation between the low-voltage control circuit and the high-voltage SCR drive circuit, enhancing safety and preventing noise from affecting the control signals. SCR1 and SCR2 are the primary switching devices that control the load, and their triggering is directly influenced by the input current from the 4-to-20 mA loop. This allows for precise control over the operation of the connected devices, making it suitable for applications where variable control is necessary, such as in dimming lights or adjusting motor speeds in response to varying input signals.
Overall, this circuit offers a robust solution for controlling high-power devices through a low-power control signal, ensuring reliability and safety in industrial applications. This circuit allows a 4-to 20-mA current loop to control an isolated SCR drive. IC1A and are one-shots. Q2 detect s zero crossings of the 120 Vac line, which triggers one-shot IC1B. IC1A causes Ql to discharge C2. When C2 recharges through R2, it triggers IC1A, and the optoisolator and SCR1/SCR2. Triggering of SCR1 and SCR2 is a function of input current, which can control motor speed, light intensity, etc.
This circuit is designed to facilitate the control of devices such as motors and lighting systems through a 4-to-20 mA current loop, which is a standard in industrial automation for transmitting analog signals. The operation begins with the detection of zero crossings from the 120 Vac line by transistor Q2. This detection is crucial for synchronizing the control signals with the AC line frequency, ensuring that the SCRs are triggered at the correct phase of the AC cycle.
IC1A and IC1B are configured as monostable multivibrators, commonly referred to as one-shots. When Q2 detects a zero crossing, it sends a pulse to IC1B, which generates a timed output pulse. This output pulse is used to control the state of the SCRs, effectively allowing for the modulation of power delivered to the load.
Simultaneously, IC1A is responsible for managing the timing of capacitor C2. When triggered, IC1A causes Q1 to discharge C2, which subsequently begins to recharge through R2. The timing characteristics of this process determine the frequency and duty cycle of the output signal to the SCRs, thereby directly influencing the power delivered to the load.
The optoisolator serves to provide electrical isolation between the low-voltage control circuit and the high-voltage SCR drive circuit, enhancing safety and preventing noise from affecting the control signals. SCR1 and SCR2 are the primary switching devices that control the load, and their triggering is directly influenced by the input current from the 4-to-20 mA loop. This allows for precise control over the operation of the connected devices, making it suitable for applications where variable control is necessary, such as in dimming lights or adjusting motor speeds in response to varying input signals.
Overall, this circuit offers a robust solution for controlling high-power devices through a low-power control signal, ensuring reliability and safety in industrial applications. This circuit allows a 4-to 20-mA current loop to control an isolated SCR drive. IC1A and are one-shots. Q2 detect s zero crossings of the 120 Vac line, which triggers one-shot IC1B. IC1A causes Ql to discharge C2. When C2 recharges through R2, it triggers IC1A, and the optoisolator and SCR1/SCR2. Triggering of SCR1 and SCR2 is a function of input current, which can control motor speed, light intensity, etc.
Circuit forms constant-current SCR
A typical silicon-controlled rectifier (SCR) requires a trigger current to latch on. Once the device is latched, the current flowing through the SCR is determined only by the external component values. The SCR lacks the ability to limit current flow...
SCR relaxation flasher
Flashing occurs each time the capacitor discharges through the turned-on SCR. When the discharge current falls below the SCR holding current, the SCR turns off, and the capacitor begins charging for another cycle. The circuit will maintain a slower but...
SLAVE FLASH TRIGGER
The SCR is connected across the trigger circuit of the flash gun. In its normal state, the SCR remains off, allowing the flash gun to charge to its trigger voltage. A phototransistor, Q1, monitors the light level. When a high-intensity...
Add-on-telephone-hold-button
A sensitive-gate SCR provides a line-holding current of 20 to 40 mA, depending on loop resistance. It also lights an LED to give the user a positive indication that the telephone line is on hold. The 20 to 40 mA...
The integrated three pulse trigger components KCZ3 electrical schematic
The KCZ3 is an integrated three-pulse triggering component designed for use in three-phase half-bridge inverters. Each phase output pulse can reliably drive a high-power thyristor and is adaptable to various phase voltages. The electrical parameters are as follows: Phase shift...
Precise One Shot Circuit
This approach utilizes a Hip-Hop, a shift register, and two gates (A). Before the one-shot pulse, the output of the NOR gate is 0. Consequently, the data input of the D-type flip-flop is equivalent to the trigger. When a trigger...
SCR_LATCH
Activates a mobile transceiver or other mobile equipment when power is applied, especially if the external circuit is interrupted during theft. The transmitter will then emit an unmodulated carrier signal even if the Push-To-Talk (PTT) switch is disconnected or turned...
Code-practice-oscillator
Capacitor C1 charges through resistor R1, and when the gate level established by potentiometer R2 is sufficiently high, the SCR is triggered. Current flows through the SCR and earphones, discharging C1. The anode voltage and current drop to a low...
Line-synchronized-driver
The gate drive that phase controls the four parallel SCRs is achieved using a complementary MOS hex gate MC14572 and two bipolar transistors. This adjustable line-synchronized driver allows SCR conduction from near zero to 180 degrees. A Schmitt trigger clocks...